Back to Blog
pool lightled conversionfrisco txpool repair

Your Pool Light Didn’t Burn Out — The Gasket Failed and It Flooded

The most common pool light failure isn’t the bulb — it’s a gasket letting water into the fixture. A reseal runs $150-300 against $450-1,500 for a color LED conversion. The energy savings don’t justify it.

John Smith, CPO-Certified Pool TechnicianNovember 17, 20265 min read

The most common pool light failure we see in Frisco isn't a dead bulb or a dead LED. It's a failed gasket letting water into the fixture. The light floods, and what looks like a burned-out bulb is actually a seal problem. And on the question everyone asks next — should I convert to LED while I'm in there — our answer is usually no, not for the reason you're being sold. A color LED fixture runs $450 to $1,500 installed against $150 to $350 for a bulb swap in a sound incandescent fixture. That's three to four times the cost, and the electricity savings do not close that gap.

The Failure: Water Gets In

A pool light fixture is an electrical device sitting underwater. The only thing keeping those two facts from colliding is a gasket sealing the lens to the housing.

When that gasket dries out, hardens, or gets damaged, water gets past it and fills the fixture. What you see from the deck:

  • Visible water inside the lens — the clearest sign
  • A hazy, dim, or yellowed light — from a flooded lens or a clouded gasket
  • The light stops working entirely

Most people see the last one and assume the bulb died. The bulb may well be dead, but it died because the housing flooded, and putting a new bulb in a fixture with a failed gasket just floods the new bulb.

This is also true of LED fixtures. LEDs usually fail at the seal rather than at the diodes. So "upgrade to LED and stop having light problems" is not quite how it works — the failure mode that actually takes out pool lights is the same one either way.

The Safety Part — Take This Seriously

Water in an energized fixture can trip the GFCI. If your pool light trips the breaker or the GFCI:

Do not repeatedly reset it, and do not swim. Turn the breaker off and have it diagnosed. A GFCI tripping on a pool light is the safety device doing exactly its job, and resetting it to see if it holds is the wrong instinct.

This is one of the few pool problems where the correct move is to stop and get a qualified eye on it rather than troubleshoot it yourself. Pool lights sit in the crossover between electrical work and underwater equipment, and a tripped breaker is easy to misread as something harmless.

What the Fix Actually Costs

The right repair depends on what failed, and the cheapest option is frequently available:

RepairTypical cost
Gasket and lens reseal (fixture otherwise fine)$150–$300
Bulb swap in a sound incandescent fixture$150–$350
White LED fixture$350–$900
Color LED fixture$450–$1,500
Junction box or deck wiring$300–$900
New conduit or niche repair$1,500+ — requires draining the pool

Notice the top line. If the gasket failed but the fixture itself is sound, a reseal is the fix, and it's the cheapest item on the list. Plenty of people get quoted a full fixture replacement for a problem that's a gasket.

On Converting to LED

Here's the honest version, because the sales pitch for LED leans on the wrong number.

The energy argument is weak. Yes, incandescent fixtures draw 300-500 watts and LEDs draw 30-70. But a pool light runs a few hours a night at most, not eight hours a day like a pump. At four hours a night, a 500-watt fixture costs roughly $40-60 a year in electricity against about $5 for an LED. Saving $35-55 a year against a $450-1,500 conversion is a decade or more of payback on energy alone. Anyone selling LED conversion on power savings is quoting you percentages instead of dollars.

The honest argument for LED is lifespan, not electricity. Incandescent bulbs last roughly one to two seasons. LEDs last years. Every incandescent bulb replacement is a part plus a service call, so over a long enough horizon the repeat visits are where the money actually goes — and that's a real consideration, not a sales line. Color options and the safer low-voltage design in a wet environment are genuine benefits too.

Where we land: don't convert a working incandescent fixture for the energy savings — the math doesn't support it. If your current fixture is sound and you need a bulb, swap the bulb. If you don't need color, a white LED is meaningfully cheaper than color. And if the pool is already being drained for resurfacing or niche work, that's the moment — doing the light while the pool is empty is far cheaper than doing it as its own job later.

That's the same test we apply to any pool upgrade: does it cut a real recurring cost or prevent an expensive failure? LED conversion does, slowly, on bulb replacement — not on your electric bill.

What to Do If Your Light Is Out

  1. Look at the lens before assuming it's the bulb. Water inside, haze, or yellowing points at the gasket.
  2. If it's tripping the GFCI or breaker, stop. Breaker off, nobody in the pool, get it diagnosed.
  3. Ask specifically whether a reseal will fix it before accepting a fixture replacement quote. If the housing is sound, $150-300 beats $450-1,500.
  4. Don't let a hazy or water-filled lens sit. Acting on it before the fixture fails completely is the difference between a reseal and a replacement.

Hydra Pool Services inspects pool lights as part of equipment checks across Frisco and 7 surrounding cities. Start your free 2-week trial →

Source: Pool light repair and LED conversion costs, wattage comparison, and gasket failure modes via True Texan Pools — Pool Light Replacement Cost.

John Smith, CPO-Certified Pool Technician

Servicing pools across Frisco, Plano, McKinney & North DFW.

Call Now — (214) 233-6803