Top 5 Reasons Your Pool Filter Isn’t Working Properly (and What to Do)
A clean filter is like the lungs of your pool. It keeps water clear, safe, and flowing the way it should. Without it, your pool turns cloudy fast. In North DFW, TX, where pools run nearly year-round, filters work harder than anywhere else. Between long summers, heavy pollen, and dust blowing in from construction or wind, they need more care than most people realize.
The average pool in Frisco, TX, or Plano, TX, runs between 10 and 12 hours every day in summer. That’s a lot of water cycling through your filter. And if you skip cleaning or forget about small issues, problems can show up quick.
According to the Pool & Hot Tub Alliance, 70% of pool clarity issues in warm states like Texas start with a dirty or failing filter. A well-maintained system can double the life of your equipment and save money on electricity too.
That’s why Hydra Pool Services offers pool filter cleaning in Frisco TX, filter maintenance in Murphy TX, and equipment repairs in Plano and McKinney TX. We help homeowners across Allen and The Colony keep their pools running strong all year.
Let’s look at the five most common reasons your pool filter stops working right — and what you can do before things get worse.
Reason #1: Clogged Filter Cartridges or Media
This one is the most common. If your pool water starts looking dull, or the jets feel weaker, you might have a clogged filter. When too much dirt, dust, and oils build up, the filter can’t let water pass through properly.
In Frisco and Murphy, TX, where trees shed pollen and dust floats around after dry spells, this happens a lot. You might even see the pressure gauge rise because the filter is fighting to push water through.
How to fix it:
Take the cartridge out and rinse it well with a garden hose.
For sand filters, backwash the system until the waste water looks clear.
If you use a DE filter, replace the diatomaceous earth after backwashing.
Replace cartridges every 12 to 18 months for best performance.
Hydra offers professional filter cleaning service in Frisco TX, and our technicians often find filters so packed with fine dust that water flow drops by half. A clogged filter can reduce pressure by up to 40%, according to industry data.
Cleaning it the right way also keeps your pump from overworking. When pumps strain, they use more electricity and wear out sooner. Regular cleaning is a simple fix that saves you money in the long run.
Reason #2: Air Leaks in the Pump or Filter System
If you see bubbles coming out of the pool jets or hear gurgling near the pump, that’s a sign of air in the system. It might sound small, but it can cause a lot of problems. Air leaks reduce pressure, mess with circulation, and can damage your pump motor over time.
In Plano, TX, and Allen, TX, we see this issue often after homeowners open the pump lid to check baskets and don’t tighten it all the way. The o-ring under that lid wears down with age, letting air slip in. Cracked fittings or suction leaks underground can also be the cause.
What to check:
Look for cracks in pipes or fittings.
Check the pump lid and o-ring. Replace if dry or flat.
Make sure the pump basket is clean and lid tight.
Watch the pressure gauge. Low readings often mean suction leaks.
Even a small air leak can cause 25% loss in pump performance. Hydra’s pool repairs in Plano TX include full system pressure testing to find leaks fast. Our technicians use non-invasive methods to check joints and seals without digging up your yard.
Air in the system might not sound serious, but if ignored, it can lead to pump overheating or full motor failure.
Reason #3: Incorrect or Neglected Backwashing
Backwashing sounds simple, but many people either do it too much or not enough. Both are bad for your filter.
If you backwash too often, you waste water and remove helpful filter media. Too little, and dirt builds up, restricting flow. A good rule is to backwash when the pressure gauge reads 8 to 10 psi higher than normal. You can mark that “clean” level with a piece of tape so it’s easy to remember.
In North DFW, TX, pools collect a lot of dust and organic debris, especially after summer storms. That debris gets trapped in your filter quickly, so backwashing should be part of your regular pool care routine.
Each backwash cycle uses around 200–300 gallons of water, according to the EPA. That’s a lot, so don’t overdo it. Hydra provides weekly filter checks and backwashing service across Frisco, Allen, and McKinney TX, ensuring you only clean when it’s actually needed.
If you notice cloudy water after backwashing, it could mean your sand or DE filter media needs replacement. It usually lasts about 5 years before it loses effectiveness.
Hydra’s technicians can inspect your system and tell if it’s time to replace the media or just give it a deep rinse.
Reason #4: Broken Pressure Gauge or Flow Meter
Sometimes your filter problem isn’t really the filter at all. It’s the gauge. The pressure gauge tells you how well your filter system is performing. If it’s stuck at zero, always high, or doesn’t move, it’s giving you wrong information. That makes it easy to either clean too soon or wait too long.
About 40% of homeowners, according to maintenance studies, misread their filter pressure because of faulty or old gauges.
You can check by turning the system off. The needle should drop back to zero. If it stays in place or jumps randomly when running, it’s time to replace the gauge.
In Allen, TX, and McKinney, TX, where equipment sits in the sun all day, gauges wear out faster. Heat and vibration from pumps dry out the internal parts. Hydra offers pool equipment repair and replacement services across the North DFW area.
Our technicians replace gauges during routine filter cleaning appointments, so you always know your readings are right. Most homeowners replace them once a year, and it costs a lot less than a repair caused by neglecting a dirty filter.
Reason #5: Wrong Pump Size or Flow Rate
You might think a bigger pump means better water flow. But in reality, too much power can damage your filter system.
We often find low pressure pool systems in North DFW where the pump and filter don’t match. Oversized pumps push too much water through, wearing out the filter grids. Undersized pumps don’t move enough water to clean properly.
Every filter has a maximum flow rate. If you exceed it, debris slips through, or worse, parts inside the filter can crack.
What to do:
Check your filter’s label for the flow rate (GPM).
Match that with your pump’s rated output.
Ask a technician to measure real flow using a gauge or meter.
Hydra specializes in pump installation and low pressure system repair in North DFW, TX. We test each system for proper circulation and help you choose the right size equipment.
The wrong pump doesn’t just shorten filter life, it also wastes money. The Department of Energy reports that using an oversized pool pump can increase energy use by 30% or more. That’s money you could save every month.
Hydra can also install energy-efficient variable speed pumps that adjust flow automatically based on your system’s needs.
Bonus Tip: Poor Water Chemistry Can Ruin a Good Filter
Even if your equipment is perfect, bad water balance can kill your filter faster than anything. High calcium levels cause scale buildup, oils clog cartridges, and algae blocks fine filter media.
In the Texas heat, chlorine burns off faster, and pH can swing in a single day. Keeping your chemistry balanced helps your filter last longer and keeps your pool looking clean.
Here’s a quick checklist for healthy water:
pH: 7.2–7.6
Alkalinity: 80–120 ppm
Calcium hardness: 200–400 ppm
Chlorine: 1–3 ppm
Hydra offers a Chemical Only Service across Murphy, Frisco, and Plano TX for pool owners who like to clean their own pool but want help with chemistry. It’s cheaper than buying chemicals yourself, and our technicians test everything on site before adding anything to the water.
Improper pH can increase filter clogging by 20%, based on results from water quality studies. That’s why regular testing is important even during cooler months when you aren’t swimming much.
When to Call a Pool Filter Professional
Sometimes no matter what you try, the water just won’t clear up. That’s when it’s time to call a professional. If you notice these signs, it’s best to get a technician out fast:
Cloudy water that won’t clear after cleaning the filter.
Pressure gauge that never changes.
Strange noises from pump or air in the system.
Filter leaking water or air bubbles returning into the pool.
Hydra’s friendly and experienced technicians serve homes all across Frisco, Murphy, Allen, Plano, McKinney, and The Colony, TX. We offer complete pool filter cleaning and pool repairs with honest quotes and detailed service notes after every visit.
One of our customers in Plano called because their pool pressure dropped suddenly. We found a small suction leak and fixed it the same day. If they had waited, it would have burned out their pump within weeks.
New customers in North DFW can also get $100 off their first month of service. Whether you need a full cleaning or just want your filter inspected, Hydra has you covered.
Keep Your Filter Running Smooth All Year
Your pool filter is the heart of your system. Taking care of it means clean, healthy water and fewer headaches later.
To recap, the top five reasons your pool filter stops working are:
Clogged cartridges or media
Air leaks in pump or filter
Incorrect or neglected backwashing
Broken pressure gauges
Wrong pump size or flow rate
Most of these can be fixed quickly if you catch them early. But ignoring them can lead to expensive repairs, cloudy water, or even damaged equipment.
Hydra Pool Services provides pool filter cleaning in Frisco TX, pool repairs in Plano TX, and full equipment inspections across North DFW, TX. Our technicians live right here in your area, so they know exactly how Texas weather affects your pool.
If you live in Murphy, Allen, McKinney, or The Colony TX, schedule a free visit today and see how easy it is to keep your pool filter running like new.
Clean filter. Clear water. Simple life. That’s the Hydra way.
